Speedstream 5200 firmware updating

Posted by / 15-Jan-2018 23:44

Speedstream 5200 firmware updating

)Could it be that, somewhere in some hidden memory there is the "original" MAC address and if it does not match with one entered in program, bad behaving starts ?The packaged installers contain and x.def, along with many other files.I agree that capacitors still could be bad, the most reliable way I will be able test them is to de-solder them from board and use an analog ohm meter in low resistance settings to check them---------------------------------------------------------------------------------- ----------------------------------------I have FW-s Optus A9P 1850 kb, Siemens A8M 1677 kb, Bigpond A8P 2888 kb and English/Portugeese A83 1808 kb------The flash chip is 2 Mb, so Bigpond FW is too big, and I have not seen any smaller version !---------------------------------------------------------------------------------- -------------------------------------------I am also not sure about the situation of the and files....these coming with FW , so any old ones gets wiped out ?Here they are:»192.168.2.1/- DHCP»192.168.2.1/- Dynamic DNS (what francoisr wanted)»192.168.2.1/ipp_- IP Passthru»192.168.2.1/- Update firmware»192.168.2.1/ras_- RAS config»192.168.2.1/- Port forwarding»192.168.2.1/- DMZ Config»192.168.2.1/- Firewall Config»192.168.2.1/- NAT/NAPT Configuration»192.168.2.1/- Host Configuration»192.168.2.1/- UPNP Configuration»192.168.2.1/- RIP Configuration 192.168.2.1/- Time Server Configuration »192.168.2.1/- Firewall Config Wizard »192.168.2.1/- FW Attack Detection System»192.168.2.1/- Firewall Snooze Control»192.168.2.1/- Gateway Server Port Config hope that helps Hi, A 6ya expert can help you resolve that issue over the phone in a minute or two.

The Speed Stream 4200 was never officially distributed via the standard retail channel and is generally only available from an ISP.These themes all relate to Firmware, Bridge Mode and Resetting to Default …If you’re experiencing unreliable performance, wanting to upgrade the firmware or simply need to reconfigure the device from scratch then resetting the Speed Stream 4200 is a task you will need to perform. If it manages to boot, I'm pretty sure you've done the flashing correctly. Speedstream D240 is powered by Project XVersion 004-D240-A8M, Build 106-65, Oct 20 2006 Expat - XML Parser Toolkit v1.2 Copyright (c) 1998-2000, Thai Open Source Software Center Ltd---System Starting---XSH: [ OK ]FLASH: AMD Am29LV160B (Bottom Boot)Getting Firmware Internal Defaults Enter MAC Address: 001122334455NVRAM: 003-1210-INT, Orcon Full Router NV'G':139678NVRAM: [ OK ]INT: [ OK ]TMR: [ OK ]WDT: Internal timeout set to 10s WDT: [ OK ]LED: [ OK ]BUTTON: [ OK ]SYSTASK: [ OK ]SNTPC: [ OK ]SYSLOG: [ OFF ]XLOG: [ OK ]DNSRELAY: [ OK ]IPFW: [ OK ]ADSL: [ OK ]BRG: [ OK ]L2XP [ OK ]ETH1: [ OK ]USB: [ OK ]2684: [ OK ]2364: [ OK ]ATM: [ OK ]IGD: [ OK ]UPNP: [ OK ]LANCLIENT: [ OK ]DDNSD: [ OFF ]FWUPDATE: [ OK ]TFTPD: [ OFF ]ARDD: [ OFF ]CWMP: [ OK ]---System Ready---ADSL: Boost DSPADSL: Data Pump Version - .00ADSL: DOWNADSL: WAITINGUPNP: Added IF: br0 to UPn P multi-cast group Reset Status Register (RSR) value: 0x1Rebooting like this is a very typical symptom of bad capacitors.

speedstream 5200 firmware updating-20speedstream 5200 firmware updating-67speedstream 5200 firmware updating-39